| Size |
Product Name |
Short Description |
Download |
| 1.32 MB |
DF-2 / DF-3 |
General purpose tool steel, good surface hardness, wear resistance, simple heat treating. |
.PDF |
| |
CARMO |
Medium alloyed steel suitable for blanking of larger structural parts where the cutting edges are flame- or induction hardened. Same chemical composition as Calmax but delivered in prehardened condition. |
|
| |
VIKING |
Versatile, high alloyed tool steel with excellent combination of toughness and wear resistance required for chipper-knives and heavy duty blanking and forming. |
|
| 908 KB |
CALDIE |
High alloyed tool steel, suitable for short to medium run tooling where chipping and/or cracking are the predominant failure mechanisms and where a high compressive strength (hardness over 60 HRC) is necessary. |
.PDF |
| 1.22 MB |
XW-10 |
Good hardenability and wear resistance. Excellent size stability. For medium runs. |
.PDF |
| 1.09 MB |
ASSAB 88 |
Mixed-abrasive profile and good resistance to chipping. Good machining and WEDM properties. |
.PDF |
| 1.02 MB |
XW-41/XW-42 |
12% Cr tool steel with high wear resistance and toughness. |
.PDF |
| 1.30 MB |
XW-5 |
12% Cr high carbon tool steel with excellent abrasive wear resistance. |
.PDF |
| 2.36 MB |
ASP 23 |
Powder HSS. Excellent wear resistance and toughness. |
.PDF |
| 1.26 MB |
ASP 30 |
Powder HSS for cutting tools. Excellent wear resistance and toughness. Good hot hardness. |
.PDF |
| 1.36 MB |
ASP 60 |
Powder HSS for cutting and cold work tools. Extreme wear resistance. High hot hardness. |
.PDF |
| 535 KB |
VANADIS 4 |
Powder tool steel for long run tooling, where high demands on adhesive wear and chipping resistance is required. |
.PDF |
| 1.46 MB |
VANADIS 4 EXTRA |
Powder tool steel for long run tooling, where high demands on adhesive wear and chipping resistance is required. |
.PDF |
| |
VANADIS 6 |
High alloyed powder metallurgical tool steel suitable for long run tooling in applications with high demands on mixed wear (abrasive/ adhesive) and chipping resistance. Blanking and forming of hard work materials are typical applications. |
|
| 1.61 MB |
VANADIS 10 |
Powder tool steel. Supreme wear resistance. |
.PDF |
| 1.93 MB |
VANCRON 40 |
A nitrided powder tool steel for the very best resistance to galling and adhesive wear. No coating normally necessary. |
.PDF |
 |
| Size |
Product Name |
Short Description |
Download |
| 1.20 MB |
618, 618 HH |
Prehardened plastic mould steel. Good polishability and good machinability. |
.PDF |
| 1.03 MB |
618 T |
Pre hardened plastic mould steel suitable for medium and large tools, requiring good surface appearance. |
.PDF |
| |
718 SUPREME |
Modified prehardened plastic mould steel. Very good polishability. |
|
| 1.14 MB |
718 HH |
Modified prehardened plastic mould steel. Very good polishability. |
.PDF |
| 1.31 MB |
NIMAX |
Prehardened mould steel with best toughness, machinability and good polishability. |
.PDF |
| 1.89 MB |
CALMAX alt. 635 |
High toughness, good wear resistance and good polishability steel for plastic moulds. |
.PDF |
| 1.87 MB |
UNIMAX |
High hardness, very good toughness. ESR for good polishability. Suitable for coating and nitriding. |
.PDF |
| |
RAMAX HH |
Stainless steel for holder blocks with excellent machinability and corrosion resistance. |
|
| 1.57 MB |
RoyAlloy |
Stainless steel for holder blocks with excellent machinability and corrosion resistance. |
.PDF |
| 1.96 MB |
STAVAX ESR alt. S136 ESR |
Stainless plastic mould steel with excellent polishability and corrosion resistance. |
.PDF |
| 2.28 MB |
MIRRAX ESR |
A combination of toughness, corrosion resistance and ability to reach uniform hardness levels throughout large cross sections, and with good polishability. |
.PDF |
| 1.22 MB |
POLMAX |
Excellent polishability. Good resistance to corrosion and wear. Good machinability. |
.PDF |
| 1.15 MB |
CORRAX |
Age hardening tool steel with superior corrosion resistance. |
.PDF |
| 1.42 MB |
ELMAX |
Powder tool steel. Stainless plastic mould steel with high wear resistance. |
.PDF |
| 503 KB |
MM 40 |
Beryllium copper for plastic moulds. Excellent heat conductivity. |
.PDF |
| 522 KB |
MM XL |
Copper alloy with high thermal conductivity, good toughness and excellent machinability. |
.PDF |
| |
PT 18 |
Beryllium copper with extremely high thermal conductivity. |
|
| |
PRODAX |
Aluminium for plastic moulds, blow moulding and vacuum moulding. |
|
|
| Size |
Product Name |
Short Description |
Download |
| |
ALVAR 14 |
Alloyed tool steel for hot forging and support parts for extrusion. |
|
| |
VIDAR SUPERIOR |
Good resistance to thermal fatigue. The steel is produced by a special melting and refining technique in order to give mechanical properties with maximum isotropy and is certified to meet a minimum average Charpy V-notch test result of 11 J. |
|
| 1.58 MB |
8407 2M |
Hot work tool steel with overall good ductility, toughness, wear resistance, hardenability and machinability. 8407 2M is specially processed to higher quality than normal AISI H13 |
.PDF |
| 1.55 MB |
8407 SUPREME |
Good resistance to thermal fatigue. A premium H13 grade that meets or exceeds NADCA 207-2003 specification. |
.PDF |
| 1.75 MB |
DIEVAR |
High performance hot work tool steel with very good resistance to heat checking, gross cracking, hot wear and plastic deformation. |
.PDF |
| |
HOTVAR |
Very good high temperature properties and high hot wear resistance steel for warm forging and extrusion. |
|
| 2.38 MB |
QRO 90 SUPREME |
Very good high temperature strength and very good thermal fatigue resistance for forming and casting of copper and brass. |
.PDF |
|
